The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for work with with split-tapered sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it in to the sprocket or pulley.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and will be purchased on a single page as the pulley you need. For make use of with 5/8” shaft sizes. Comes with set screws. Extra Features: Made of Steel For use with cast iron bushed bore pulley
Our stock metal Split Taper bushings feature wrench torque capacity from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are used on sheaves, pulleys, sprockets and equipment belt pulleys. The split tapered bushing alleviates the necessity to have a component bored to size, ideally lowering on hand requirements and allowing for alterations in shaft size if necessary. The barrel of the split tapered bushing is normally split in two areas and is usually keyed to the shaft. The barrel OD is also keyed to the travel component as well. The advantage of the split tapered bushing could it be will hold, regardless if the fasteners become loose. Split tapered bushings will be interchangeable between manufacturers.
Taper bushing are trusted together with sprockets, v-belt pulleys, timing pulleys, coupling and other mechanical parts with taper bore connections.
Taper bushing series are made of high quality engineered resources with great tolerance. The feature is easy to employ and needs no extra alteration. These bushings can go well with almost all kinds of assemblies and sizes. They are the best choice in design for mechanical connections.
To complete designations add bore size. For instance: PD1215X16MM designates a 1215 taper bushing with a 16mm bore.
No costly re-boring: total selection of both metric and imperial obtainable.
Standard range matches up to 125mm/5″ shafts & Hub diameter required will depend on the application.
Complete brief reach range available, for compact lightweight assemblies & Clean, Compact Style.
Ease of installation and removal.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and may be purchased on the same page as the pulley you will need.
For use with 1 3/16” shaft sizes.
Includes 2 set screws.
Additional Features:
Made of Steel
For use with cast iron bushed bore pulley
This U1 Bushing with 5-1/2″ bore is a high-quality precision product that’s built for strength and strength. U1 bushings are used in an extensively wide variety of applications, which includes; sprockets, shaves, pulleys, gears, plus much more, we as well offer most of these items. What units this bushing apart is the high-quality steel building along with exact manufacturing and top quality control; this means that you always get a premium quality consistent product. What really sets us apart from the other guys is our experienced expert staff members and our company-wide goal of customer satisfaction.
1. Be sure the tapered cone floors of the bushing and the within of the driven product are clean and free of anti-seize lubricants.
2. Place the bushing in sprocket or different component type that accepts the bushing.
3. Place cap screws loosely in pull-up holes. The bushing remains loose to make sure sliding suit on shaft.
4. With important on shaft, slide the sprocket or other portion type to the desired placement on the shaft. Be sure to leave the heads of the cap screws available.
5. Align the sprocket or part type, tighten the screws alternatively and progressively until they happen to be pulled up tight. Usually do not employ extensions on the wrench handles and don’t permit the sprocket or component to always be drawn i contact with flange of bushing. At this stage there should be a gap between the bushing flange and sprocket, make sure this gap does not close.
Double split barrel ensures concentricity
Grips the shaft with great clamp fit
High torque carrying capacity
Permits blind assembly
Load not carried or limited by mounting screws
External key of all sizes for great drive and better torque carrying capabilities
Double-split barrel for confident clamping
Solid flange to keep up concentric bores
Available in inches, metric, and spline bores. Bore range from 3/8″ to 10″
Solid Flange & Double Split Barrel – Assures better concentricity to the shaft.
Key to Key Travel – With keys about both shaft and product to supply the strongest possible travel.
3/4″ per Foot Taper on Barrel – Personal locking taper provides the highest amount of mechanical locking merchandise to product.
The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for apply with split-tapered sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and may be purchased on the same page as the pulley you need. For use with 5/8” shaft sizes. Comes with set screws. Further Features: Made of Steel For use with cast iron bushed bore pulley
Our 
stock steel Split Taper bushings feature wrench torque capability from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are utilized on sheaves, pulleys, sprockets and gear belt pulleys. The split tapered bushing alleviates the necessity to have a component bored to size, preferably lowering readily available requirements and enabling adjustments in shaft size if important. The barrel of the split tapered bushing can be split in two locations and can be keyed to the shaft. The barrel OD can be keyed to the drive component as well. The advantage of the split tapered bushing could it be will hold, whether or not the fasteners turn into loose. Split tapered bushings are interchangeable between manufacturers.